Tank water heaters are a dependable way to provide a fast supply of hot water for your home. The addition of a storage tank ensures some hot water is readily available. But over time, other substances may accumulate in the storage tank. This could be sediment or mineral buildup originating from the main water line or an opening in the pipes. Whatever the culprit is, this buildup can reduce the efficiency of water heaters. In severe cases it can plug up drainage and might even lead to premature failure.
Thankfully, draining your water heater and removing sediment buildup is a relatively simple task. A certified plumber in the U.S. can handle the process, but you can also drain the tank on your own if you know what you’re doing. Whatever you choose, draining the tank now can help lower the risk you’ll need premature water heater replacement.
Before you start draining the tank, you’ll want to shut off the cold water supply. The supply valve connects your water heater with the main water line. Unless you have access to a well (and you may need to drain the tank more often if you do), the water main provides all the potable water your home uses. Keeping the valve sealed will stop more water from flowing into the tank, allowing you to completely empty it.
You’ll also want to grab a rubber hose, like one you would use for yard work. The hose allows you to safely drain the water heater tank without spilling water in your garage, utility closet, attic or wherever the water heater is kept. Make sure you leave the other end of the hose far away from your home to prevent the water from flowing back inside.
Finally, a screwdriver should help you loosen tight screws or valves. You shouldn’t need any more tools than this unless you come across a problem with the water heater or adjacent piping. At that point, it might be best to hire a certified plumber in the U.S..
After you’ve turned off the water supply, you can shut off the water heater itself. This will be on the thermostat for natural gas water heaters or via a breaker switch for electric models. The pilot setting on gas water heaters can continue to stay on during flushing, but electric models must be completely off. This is due to the heating elements electric water heaters use, which remain submerged. In an empty tank, they may quickly overheat. You should also review the model’s manual, as some water heaters must be completely full before the heating elements are started.
Even after you’ve shut off the water heater, you’ll have to wait for the water stored in the tank to cool down. It may be hours before the water cools to a safe temperature, so it is often best to leave the remaining steps for the following day.
Tank water heaters possess a drain valve you can use to empty the storage tank. Once you’re sure the water supply is disconnected and the water heater itself is off, locate the drain valve. Some models may have it covered up. Make sure the hose is firmly attached to prevent spilling hot water near you and the water heater.
Your home’s plumbing uses pressure inside the piping to maintain a consistent flow of water from the main water line to the rest of the house. This pressure needs to be relieved before the hot water can actually flow from the tank. By heading to the nearest faucet or spigot, you’ll release the pressure inside the piping. All you have to do is open the hot water tap to relieve the pressure before heading back to the water heater.
Keep in mind that this water may still have some residual heat. Open the drain valve and allow all the water to drain from the tank. This should carry sediment buildup out of the tank and away from your home. But some buildup may be stuck to the inside of the tank. Turning the cold water supply back on will help wash away stubborn minerals and other substances from the tank.
Keep repeating this step until the water looks clear of sediment or minerals. If the drain isn’t working because of a clog, a trained plumber is likely required.
If everything proceeds normally, you should be able to take care of most excess sediment hiding inside your water heater. Retighten the drain valve, disconnect the hose and open the water supply to get things working again. As the water heater tank begins to fill, head back to the hot water tap you opened. Once cold water starts to flow, you know the pressure is back at appropriate levels.
At this point, you can open the gas valve or flip the breaker switch back on. Like we mentioned earlier, don’t forget that some models may need to be entirely full before the water can be safely heated. Make sure you look through your manufacturer’s instructions before starting the process.
Tank water heaters are still a great option for supplying your hot water needs. Draining the tank every 1-2 years will help flush sediment buildup and keep things running at maximum efficiency. If you think your water heater is past the point of efficient heating, consider looking for water heater replacement in the U.S. from a technician you trust.
If you’re reading this, it’s probably because you just had an icy cold shower or turned on the faucet to discover that your house doesn’t have hot water. It’s a frustrating situation, but don’t fret. Learning the most likely causes of no hot water is the first step toward finding an... Continue reading
Your faucets, showerheads and plumbing appliances consume lots of hot water. Believe it or not, the Department of Energy says that water heating is the second-largest utility cost behind space heating and cooling, accounting for approximately 18% of your monthly bill. Discover how much energy... Continue reading
If you have a tankless water heater, then you know that it can run hot and cold on occasion. This is because tankless heaters are made to run without any delays as they heat water. It’s not unusual for tankless heaters to be running on high one second and low the next. The problem is that... Continue reading
© 2023 Service Experts, Service Experts Heating & Air Conditioning, and the Service Experts logo and design are registered trademarks of Service Experts LLC and used under license by SE Canada Inc. All Rights Reserved. *Not applicable to the Advantage Program. See your signed Advantage Program Agreement for full details and exclusions. 100% Satisfaction Guarantee is subject to certain restrictions and limitations as set forth in the applicable Terms and Conditions.